楞型選擇不當

Improper selection of corrugated shapes

瓷磚A的高度高，同樣的紙，雖然有很好的豎向抗壓能力，但在平面抗壓方面不如B型和C型，產品裝入瓷磚的紙箱后，紙箱在運輸過程中，會受到橫向和縱向的振動，包裝與紙箱之間的反復撞擊，會使彩盒紙箱壁變薄，產生一種現象。

Ceramic tile A has a high height, and although the same paper has good vertical compression resistance, it is not as good as B-type and C-type in terms of flat compression resistance. After the product is loaded into the ceramic tile cardboard box, the cardboard box will be subjected to horizontal and vertical vibrations during transportation. The repeated impact between the packaging and the cardboard box will cause the wall of the color box to become thinner, resulting in a phenomenon.

2. 成品鐵鍬堆放的影響

2. Impact of finished product shovel stacking

產品在成品倉庫堆放的時候，一般會堆得很高，一般有兩鏟高，在紙箱堆垛過程中，紙箱尤其是底部紙箱的強度變化是一個“蠕變”過程，表現為長期作用在紙箱上的相對穩定的載荷，紙箱在靜載荷作用下會不斷彎曲變形，如果長時間保持靜壓，紙箱會塌陷損壞，所以堆放在鐵鍬上的下層紙箱經常會膨脹，有的還會被壓壞，當紙箱受到垂直壓力時，紙箱表面中心變形較大，壓潰后的折痕呈現拋物線狀和鼓包狀，試驗表明，瓦楞紙箱受壓時，四角強度較好，但橫邊中點強度較差，所以上鏟板的腳直接壓在紙箱中間，造成紙箱中間集中受力，會造成紙箱開裂或變形，因?yàn)殓P板的縫隙太寬，紙箱的邊角掉進去，會造成紙箱過胖或鼓包。

When products are stacked in finished product warehouses, they are usually stacked very high, usually two shovels high. During the process of stacking cardboard boxes, the strength change of the cardboard boxes, especially the bottom cardboard boxes, is a "creep" process, manifested as a relatively stable load acting on the cardboard boxes for a long time. The cardboard boxes will continuously bend and deform under static load. If static pressure is maintained for a long time, the cardboard boxes will collapse and be damaged, Therefore, the lower carton stacked on the shovel will often expand, and some will be crushed. When the carton is under vertical pressure, the center of the surface of the carton will deform greatly, and the creases after crushing will appear parabolic and bulging. The test shows that when the corrugated carton is under pressure, the strength of the four corners is good, but the strength of the midpoint of the horizontal edge is poor, so the foot of the upper shovel board will press directly in the middle of the carton, causing concentrated stress in the middle of the carton, which will cause cracking or deformation of the carton, Because the gap between the shovel board is too wide, the corners of the cardboard box will fall in, causing the cardboard box to become too fat or bulging.

湘潭市金鷹彩色印刷有限公司

Xiangtan Jinying Color Printing Co., Ltd

3. 盒子高度的精確尺寸沒有確定

3. The exact size of the box height has not been determined

一般碳酸飲料盒和水箱的紙箱高度確定為裝有內容物的瓶子的瓶高加上2mm左右，紙箱堆放時長時間承受靜載荷，運輸過程中受到?jīng)_擊、振動、顛簸，使紙箱壁厚變薄，增加了一部分高度，使紙箱高度遠高于瓶子，從而使紙箱胖或鼓包更加明顯。

The height of the cardboard boxes for carbonated beverage boxes and water tanks is generally determined as the height of the bottle containing the contents plus about 2mm. The cardboard boxes bear static loads for a long time during stacking, and are subjected to impacts, vibrations, and bumps during transportation, resulting in a thinning of the cardboard box wall thickness and an increase in height, making the cardboard box much higher than the bottle, thereby making the box more bulky or bulging.

彩盒包裝生產廠家：解決彩盒紙箱肥袋或鼓包問題的措施

Color box packaging manufacturer: measures to solve the problem of fat bags or bulging in color box and cardboard boxes

1. 將紙箱的波紋形狀確定為合適的波紋形狀，在a型、c型和b型的波紋形狀中，b型的波紋高度較低，雖然垂直耐壓差，但是平面耐壓更好，采用B型瓦楞紙箱后，雖然空箱抗壓強度會降低，但內容物具有自彈性，支撐，堆垛時能承受部分堆垛重量，因此產品的堆垛效果也較好，在生產實踐中，可根據具體情況選擇不同類型的棱。

1. Determine the appropriate corrugated shape of the cardboard box. Among the corrugated shapes of A, C, and B, the corrugated height of B is lower. Although the vertical pressure resistance is poor, the planar pressure resistance is better. After using B-type corrugated cardboard boxes, although the compressive strength of the empty box will decrease, the content has self elasticity, support, and can withstand some of the stacking weight during stacking. Therefore, the stacking effect of the product is also good. In production practice, Different types of edges can be selected according to specific circumstances.

2. 改善倉庫中產品的堆放條件

2. Improve the stacking conditions of products in the warehouse

如果倉庫位置允許，盡量不要把兩把鐵鍬堆得越高越好，如果需要將兩鏟堆高，為了防止成品堆放時載荷集中，可以在堆放中間夾一個瓦楞紙板或者使用平鏟。

If the warehouse location allows, try not to stack the two shovel as high as possible. If it is necessary to stack the two shovels high, in order to prevent the load concentration when stacking finished products, a corrugated cardboard can be clamped in the middle of the stack or a flat shovel can be used.

3. 確定準確的紙箱尺寸，為了減少肥袋或鼓包現象，表現出良好的堆疊效果，我們將紙箱高度設置為與瓶高相同，特別是對于紙箱高度相對較高的碳酸飲料紙箱和純水箱。

3. Determine the accurate size of the cardboard box. In order to reduce the phenomenon of fat bags or bulges and demonstrate good stacking effect, we set the height of the cardboard box to be the same as the height of the bottle, especially for carbonated beverage cardboard boxes and pure water tanks with relatively high cardboard box height.